init repo

README.md

@@ -0,0 +1,22 @@
+# SIMM-30
+
+## Печатная плата для модуля памяти ретро компьютеров
+
+Переходные отверстия контактных площадок SIPP ready - можно установить угловые круглые штыри, а на материнскую плату обычные цанговые панели.
+Проект выполнен в pcad 2006 sp2.
+
+## Особенности:
+- SMUC не будет правильно работать с модулем simm30-1x-1M, ему нужны модули с типом памяти simm30-8x-1M;
+- толщина платы должна быть тоньше стандартных 1.6мм, т.к. она не будет входить в разъем. Оптимальная толщина 1.4мм, но не все производители печатных плат могут изготавливать такие. Можно изготавливать 1.2мм, в случае если такая плата будет "неконтачить" в разъеме, можно напаять немного олова на все контактные площадки. Вариант проще - поместить с одной стороны полоску бумаги;
+
+## Модуль представлен в трех вариантах:
+- 1мб, на одной микросхеме памяти 1M x 16, типа GM71C18163C
+<br><img src="photos/simm30-1x-1M.jpg" width="500" />
+
+- 1мб, на восьми микросхемах памяти 1M x 1, типа TC511000P
+<br><img src="photos/simm30-8x-1Ma.jpg" width="500" />
+<br><img src="photos/simm30-8x-1Mb.jpg" width="500" />
+
+- 256кб, на восьми микросхемах памяти 256K x 1, типа TMS4256, KM41C256, 565РУ7
+<br><img src="photos/simm30-8x-256Ka.jpg" width="500" />
+<br><img src="photos/simm30-8x-256Kb.jpg" width="500" />

simm30-1x-1M.drc

@@ -0,0 +1,264 @@
+P-CAD Design Rule Check Report
+
+======================================================================
+
+C:\prj\1. SIMM-30\simm30-1x-1M.drc:
+
+
+Design Clearances (in   mm):
+-------------------------------
+Board Edge Clearance:   Not Defined
+Silk Screen Clearance:  Not Defined
+Hole-Hole Clearance:    Not Defined
+
+
+Layer Clearances (in   mm):
+-------------------------------
+
+Layer Name          Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+Top                   0.150     0.150     0.150     0.150     0.150     0.150
+Bottom                0.150     0.150     0.150     0.150     0.150     0.150
+
+
+Net Class Clearances (in   mm):
+-------------------------------
+Net Class Name      Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+
+
+Net Clearances (In   mm):
+-------------------------
+Net Name            Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+
+Net Class To Net Class Clearances (in   mm):
+--------------------------------------------
+Net Class Names     Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+
+
+Area Checked:
+-------------
+
+DRC Extents:            Entire Workspace
+
+
+DRC Report Options:
+-------------------
+
+Net List Compare:                       Off
+Clearance Violations:                   On
+Text Violations:                        On
+Same-Parent-Component Pad Violations:   On
+Net List Violations:                    On
+Unrouted Nets:                          On
+Unconnected Pins:                       Off
+Net Length Violations:                  On
+Silk Violations:                        On
+Copper Pour Violations:                 On
+Plane Violations:                       On
+Component Violations:                   On
+Drill Violations:                       On
+
+----------------------------------------------------------------------
+
+24-Jan-25  05:33                                            Page    1
+
+P-CAD Design Rule Check Report
+
+======================================================================
+
+Test Point Violations:                  Off
+
+DRC Errors:
+-----------
+
+
+NETLIST VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+CLEARANCE VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+UNROUTED NETS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+Warning: Net length violation tests were not performed because
+         of missing MinNetLength, MaxNetLength, or MatchedLength rules.
+
+NETLIST LENGTH VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+SILK SCREEN CLEARANCE VIOLATIONS:
+
+
+Warning: Silk Screen clearance violation tests were not performed because
+         of missing SilkscreenClearance rule.
+
+0 warning(s) detected.
+0 error(s) detected.
+
+TEXT VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+WIDTH VIOLATIONS:
+
+Warning: Width violation tests were not performed because
+         of missing Width rule.
+
+0 warning(s) detected.
+0 error(s) detected.
+
+COPPER POUR VIOLATIONS:
+
+
+----------------------------------------------------------------------
+
+24-Jan-25  05:33                                            Page    2
+
+P-CAD Design Rule Check Report
+
+======================================================================
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+PLANE VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+COMPONENT VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+DRILL VIOLATIONS:
+
+Warning: Hole to hole clearance violation tests were not performed because
+         of missing HoleToHoleClearance rule.
+
+0 warning(s) detected.
+0 error(s) detected.
+
+DRC Summary:
+------------
+
+Netlist:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Clearance:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Unrouted Nets:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Net Length:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Silk Screen:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Text:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Width:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Copper Pour:
+	Errors:         0
+
+----------------------------------------------------------------------
+
+24-Jan-25  05:33                                            Page    3
+
+P-CAD Design Rule Check Report
+
+======================================================================
+
+	Warnings:       0
+	Ignored Errors: 0
+Plane:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Component:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Drilling:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+----------------------------------------------------------------------
+
+24-Jan-25  05:33                                            Page    4
+

simm30-8x-1M.drc

@@ -0,0 +1,191 @@
+C:\prj\SIMM30\simm30-8x-1M.drc:
+
+
+Design Clearances (in   mm):
+-------------------------------
+Board Edge Clearance:   Not Defined
+Silk Screen Clearance:  Not Defined
+Hole-Hole Clearance:    Not Defined
+
+
+Layer Clearances (in   mm):
+-------------------------------
+
+Layer Name          Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+Top                   0.200     0.200     0.200     0.200     0.200     0.200
+Bottom                0.200     0.200     0.200     0.200     0.200     0.200
+
+
+Net Class Clearances (in   mm):
+-------------------------------
+Net Class Name      Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+
+
+Net Clearances (In   mm):
+-------------------------
+Net Name            Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+
+Net Class To Net Class Clearances (in   mm):
+--------------------------------------------
+Net Class Names     Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+
+
+Area Checked:
+-------------
+
+DRC Extents:            Entire Workspace
+
+
+DRC Report Options:
+-------------------
+
+Net List Compare:                       Off
+Clearance Violations:                   On
+Text Violations:                        On
+Same-Parent-Component Pad Violations:   On
+Net List Violations:                    On
+Unrouted Nets:                          On
+Unconnected Pins:                       Off
+Net Length Violations:                  On
+Silk Violations:                        On
+Copper Pour Violations:                 On
+Plane Violations:                       On
+Component Violations:                   On
+Drill Violations:                       On
+Test Point Violations:                  Off
+
+DRC Errors:
+-----------
+
+
+NETLIST VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+CLEARANCE VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+UNROUTED NETS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+Warning: Net length violation tests were not performed because
+         of missing MinNetLength, MaxNetLength, or MatchedLength rules.
+
+NETLIST LENGTH VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+SILK SCREEN CLEARANCE VIOLATIONS:
+
+
+Warning: Silk Screen clearance violation tests were not performed because
+         of missing SilkscreenClearance rule.
+
+0 warning(s) detected.
+0 error(s) detected.
+
+TEXT VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+WIDTH VIOLATIONS:
+
+Warning: Width violation tests were not performed because
+         of missing Width rule.
+
+0 warning(s) detected.
+0 error(s) detected.
+
+COPPER POUR VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+PLANE VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+COMPONENT VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+DRILL VIOLATIONS:
+
+Warning: Hole to hole clearance violation tests were not performed because
+         of missing HoleToHoleClearance rule.
+
+0 warning(s) detected.
+0 error(s) detected.
+
+DRC Summary:
+------------
+
+Netlist:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Clearance:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Unrouted Nets:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Net Length:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Silk Screen:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Text:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Width:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Copper Pour:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Plane:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Component:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Drilling:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+
+----------------------------------------------------------------------
+
+21-Oct-23  18:04                                            Page    1
+

simm30-8x-256K.drc

@@ -0,0 +1,264 @@
+P-CAD Design Rule Check Report
+
+======================================================================
+
+C:\prj\SIMM30\simm30-8x-256K.drc:
+
+
+Design Clearances (in   mm):
+-------------------------------
+Board Edge Clearance:   Not Defined
+Silk Screen Clearance:  Not Defined
+Hole-Hole Clearance:    Not Defined
+
+
+Layer Clearances (in   mm):
+-------------------------------
+
+Layer Name          Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+Top                   0.200     0.200     0.200     0.200     0.200     0.200
+Bottom                0.200     0.200     0.200     0.200     0.200     0.200
+
+
+Net Class Clearances (in   mm):
+-------------------------------
+Net Class Name      Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+
+
+Net Clearances (In   mm):
+-------------------------
+Net Name            Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+
+Net Class To Net Class Clearances (in   mm):
+--------------------------------------------
+Net Class Names     Pad-Pad  Pad-Line Line-Line   Pad-Via  Via-Line   Via-Via
+
+
+
+Area Checked:
+-------------
+
+DRC Extents:            Entire Workspace
+
+
+DRC Report Options:
+-------------------
+
+Net List Compare:                       Off
+Clearance Violations:                   On
+Text Violations:                        On
+Same-Parent-Component Pad Violations:   On
+Net List Violations:                    On
+Unrouted Nets:                          On
+Unconnected Pins:                       Off
+Net Length Violations:                  On
+Silk Violations:                        On
+Copper Pour Violations:                 On
+Plane Violations:                       On
+Component Violations:                   On
+Drill Violations:                       On
+
+----------------------------------------------------------------------
+
+21-Oct-23  17:34                                            Page    1
+
+P-CAD Design Rule Check Report
+
+======================================================================
+
+Test Point Violations:                  Off
+
+DRC Errors:
+-----------
+
+
+NETLIST VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+CLEARANCE VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+UNROUTED NETS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+Warning: Net length violation tests were not performed because
+         of missing MinNetLength, MaxNetLength, or MatchedLength rules.
+
+NETLIST LENGTH VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+SILK SCREEN CLEARANCE VIOLATIONS:
+
+
+Warning: Silk Screen clearance violation tests were not performed because
+         of missing SilkscreenClearance rule.
+
+0 warning(s) detected.
+0 error(s) detected.
+
+TEXT VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+WIDTH VIOLATIONS:
+
+Warning: Width violation tests were not performed because
+         of missing Width rule.
+
+0 warning(s) detected.
+0 error(s) detected.
+
+COPPER POUR VIOLATIONS:
+
+
+----------------------------------------------------------------------
+
+21-Oct-23  17:34                                            Page    2
+
+P-CAD Design Rule Check Report
+
+======================================================================
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+PLANE VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+COMPONENT VIOLATIONS:
+
+
+0 warning(s) detected.
+0 error(s) detected.
+
+DRILL VIOLATIONS:
+
+Warning: Hole to hole clearance violation tests were not performed because
+         of missing HoleToHoleClearance rule.
+
+0 warning(s) detected.
+0 error(s) detected.
+
+DRC Summary:
+------------
+
+Netlist:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Clearance:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Unrouted Nets:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Net Length:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Silk Screen:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Text:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Width:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Copper Pour:
+	Errors:         0
+
+----------------------------------------------------------------------
+
+21-Oct-23  17:34                                            Page    3
+
+P-CAD Design Rule Check Report
+
+======================================================================
+
+	Warnings:       0
+	Ignored Errors: 0
+Plane:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Component:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+Drilling:
+	Errors:         0
+	Warnings:       0
+	Ignored Errors: 0
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+----------------------------------------------------------------------
+
+21-Oct-23  17:34                                            Page    4
+